Hoffman amps Boardmaker instructions

Page - Board Page 0 - Board Page 1 - Board Page 2 - Board Page 3 - Board Page 4 - Board Page 5 - Board Page 6
To follow along with these pages you should go here to the library page and print out the layout diagram for the 5F6A Bassman board.

At this point we have built our complete circuit board and our pot harness. The last thing I did before I shipped a board kit was to assemble the bag of goodies that are needed to install the board kit in an amp. The exact items that came with each kit would vary, for example you don't get 4-12A jacks with a 6G15 reverb kit, the jacks are on the pot harness assembly. The actual parts listings on this page are a better guide as to what each kit needed or did not need. You can also see pictures of the bag of goodies on the old board kit page.

This is the general list of parts not specific to any one board.

1 - Set of instructions.
1 - Layout diagram.
1 - Circuit board with all mounting hardware (standoffs, screws, nuts)
1 - Pot harness assembly.
4 - #12A 1/4" input jacks.
4 - 68k input jack resistors.
2 - 1meg input jack resistors.
2 - 1.5k Fender or 2 - 5.6k Marshall or 4 - 1.5k Vox grid stopper resistors.
4 - Round terminal lugs for chassis ground connections.
5 ft each of assorted green, red, black and white wire. 20 gauge solid and 18 gauge stranded.
Shielded cable for input jacks.
Heat shrink tubing for shielded cable.
2 - 6.8k mid control resistors on the AB763 kit.
1 – 220k reverb jack resistor on the AB763 and Reverb unit kits.

5E3, 5F6A, Plexi and AC30 bag of goodies

1 - Set of instructions.
1 - Layout diagram.
1 - Circuit board with all mounting hardware (standoffs, screws, nuts)
1 - Pot harness assembly.
4 - #12A 1/4" input jacks.
4 - 68k input jack resistors.
2 - 1meg input jack resistors.
2 - 1.5k Fender or 2 - 5.6k Marshall or 4 - 1.5k Vox grid stopper resistors.
4 - Round terminal lugs for chassis ground connections.
5 ft each of assorted green, red, black and white wire. 20 gauge solid and 18 gauge stranded.
2 ft Shielded cable for input jacks.
2 inch Heat shrink tubing for shielded cable.

AB763 bag of goodies

1 - Set of instructions.
1 - Layout diagram.
1 - Circuit board with all mounting hardware (standoffs, screws, nuts)
1 - Pot harness assembly.
4 - #12A 1/4" input jacks.
4 - 68k input jack resistors.
2 - 1meg input jack resistors.
2 - 1.5k Fender grid stopper resistors.
4 - Round terminal lugs for chassis ground connections.
5 ft each of assorted green, red, black and white wire. 20 gauge solid and 18 gauge stranded.
2 ft Shielded cable for input jacks.
2 inch Heat shrink tubing for shielded cable.
2 - 6.8k mid control resistors.
1 – 220k reverb jack resistor.

6G15 bag of goodies

1 - Set of instructions.
1 - Layout diagram.
1 - Circuit board with all mounting hardware (standoffs, screws, nuts)
1 - Pot harness assembly.
4 - Round terminal lugs for chassis ground connections.
5 ft each of assorted green, red, black and white wire. 20 gauge solid and 18 gauge stranded.
2 ft Shielded cable for input jacks.
2 inch Heat shrink tubing for shielded cable.
1 – 220k reverb jack resistor.

Enter My Tube Amp Parts Store Here

Mobile users Enter My Tube Amp Parts Store Here

The Tube amp Library of information
Click the link above for Tube amp info, Schematics, Board building information, Projects, Mods, Transformer diagrams, Photo's, Sound clips.
There are hundreds of pages of Tube amp information on my library page.

Please visit my Tube Amplifier Forum
Here's the place you can go to ask tube amplifier questions.
You will find a large community of friendly amp builders at the link above.

Check the huge library of Schematics here

Design your own custom Turret Board or Eyelet board

DIY Layout Creator file analyzer program

DIY Layout Creator file library

How to email me

MEMBER OF PROJECT HONEY POT
Spam Harvester Protection Network
provided by Unspam