18 Watt stout with Reverb and Hot switch.
This is not a kit, it is a parts listing from my project build. |
|
| Back to library page | |
| Qty | Description of part |
| 1 | 18 Watt chassis, see my chassis page. |
| Back panel parts | |
| 6 | 9 pin tube sockets that fits your chassis |
| 3 | 12AX7 pre amp tubes |
| 1 | 12AT7 reverb driver tube |
| 2 | EL84 power tubes |
| 2 | EL84 spring clips |
| 1 | 8 pin tube socket that fits your chassis - rectifier tube |
| 1 | Sovtek tube spring retainer - rectifier tube |
| 1 | 5Y3 Rectifier Tube |
| 1 | rotary impedance selector switch |
| 1 | Knob of your choice |
| 2 | 12A jacks - speaker and foot switch |
| 2 | RCA jacks - reverb send, return and foot switch |
| 1 | IEC 12 Foot Power cord |
| 1 | IEC Power cord receptacle |
| 1 | Fender style Fuse holder for mains |
| 1 | main Slo-blo fuse 2 amp |
| Front panel parts | |
| 1 | LED Lamp assembly |
| 1 | 180 Ohm LED current limiting resistor |
| 2 | Spst Carling power and Standby switch |
| 4 | Knobs of your choice |
| 4 | Pots, 2-500KA, 1-1MA, 1-250KL |
| 2 | 12A input jacks |
| Top chassis parts | |
| 1 | 18 Watt power tranny with 5 volt tap |
| 1 | 18 Watt output tranny with 4, 8 and 16 ohm taps |
| 1 | 125C3A choke |
| 1 | 022921 Reverb Transformer |
| Off board 1/2 watt resistors | |
| 2 | 100 ohm - heater center tap |
| 1 | 100K - pots |
| 2 | 8.2K - EL84 grid stoppers |
| 1 | 220K - reverb jack |
| 2 | 68K - input jack |
| 1 | 1M - input jack |
| Off board misc. | |
| 5 ft | Each Red, Black, White, Green 20GA Solid core wire |
| 5 ft | 18 Gauge Heater wire |
| 20 ft | Mini shielded cable - general wiring and reverb cables |
| 5 | #8 Ring terminals |
| 12 inches | Heat shrink tubing |
| 1 | 8 Lug terminal strip |
| 1 | 4AB3C1B or 9AB3C1B reverb tank |
| 4 | RCA Plugs - Reverb cables |
| Assortment of #4, #6 and #8 screws, nuts and washers, depending on what you are mounting. Get 20 of each to have on hand. | |
| Circuit board 1/2 watt resistors | |
| 3 | 820 OHM |
| 2 | 2.2K |
| 1 | 47K |
| 6 | 100K |
| 5 | 470K |
| Circuit board 3 watt resistors | |
| 3 | 4.7K |
| 1 | 2.2K |
| 2 | 1K |
| Circuit board 10 watt resistors | |
| 1 | 130 Ohm |
| Circuit board capacitors | |
| 1 | 250P |
| 1 | 500P |
| 3 | .68/250V |
| 1 | .0047 Mallory 150 - 400 volt or higher |
| 2 | .01 Mallory 150 - 400 volt or higher |
| 4 | .022 Mallory 150 - 400 volt or higher |
| 1 | 22uf/50v cathode cap |
| 1 | 47uf/100v cathode cap |
| 6 | 22uf/500v power supply cap |
| Circuit board misc. | |
| 5 | 1/4" Nylon standoffs |
| 5 | #8 x 5/8" screws |
| 5 | #8 Nuts |
| 1 | 1/8" Thick circuit board x 11 inches long |
| 59 | Turret lugs |
| On board Relay stuff | |
| 1 | Relay socket |
| 1 | 5 volt signal switching relay |
| 1 | 1N4001 or 1N4007 Diode |
| Relay power supply board | |
| 1 | Bridge #1 - See my web catalog |
| 2 | 4700uf/16V caps |
| 1 | 1/2 watt dropping resistor - 100 ohm will work |
| 1 | 1/8" Thick circuit board x 1.5" wide x 3" long |
| 7 | Turret lugs |
Enter My Tube Amp Parts Store Here
Mobile users Enter My Tube Amp Parts Store Here
The Tube amp Library of information
Click the link above for Tube amp info, Schematics, Board building information, Projects, Mods, Transformer diagrams, Photo's, Sound clips.
There are hundreds of pages of Tube amp information on my library page.
Please visit my Tube Amplifier Forum
Here's the place you can go to ask tube amplifier questions.
You will find a large community of friendly amp builders at the link above.
Check the huge library of Schematics here
Design your own custom Turret Board or Eyelet board
DIY Layout Creator file analyzer program
DIY Layout Creator file library
How to email me
|
MEMBER OF PROJECT HONEY POT Spam Harvester Protection Network provided by Unspam |