18 watt Stout R1 with Hot switch.
This is not a kit, it is a parts listing from my project build. |
|
| Back to library page | |
| Qty | Description of part |
| 1 | Suitable Chassis of your choice - I do not stock a small Stout chassis. |
| Back panel parts | |
| 1 | Rotary impedance selector switch |
| 1 | Knob of your choice |
| 2 | #11 jacks speaker jacks |
| 1 | 12 Foot Power cord |
| 1 | Fender style Fuse holders for mains |
| 1 | Slo-blo fuse 1 amp |
| 1 | Spst Carling power switch |
| Front panel parts | |
| 1 | LED Lamp assembly |
| 1 | 180 Ohm LED current limiting resistor |
| 2 | Knobs of your choice |
| 2 | pots 2 x 500KA |
| 1 | 12A input jack |
| 1 | SPST mini toggle switch - relay only |
| Top chassis parts | |
| 4 | 9 pin tube sockets that fits your chassis |
| 2 | 12AX7 pre amp tubes |
| 2 | EL84 power tubes |
| 2 | EL84 spring clips |
| 1 | 8 pin tube socket that fits your chassis - rectifier tube |
| 1 | 5Y3 Rectifier Tube |
| 2 | Sovtek EL84 tube spring retainer2 |
| 1 | 18 Watt power tranny with 5 volt tap |
| 1 | 18 Watt output tranny with 4, 8 and 16 ohm taps |
| Off board 1/2 watt resistors | |
| 2 | 100 ohm - heater center tap |
| 1 | 100K - pots |
| 2 | 8.2K - EL84 grid stoppers |
| 1 | 1M - input jack |
| Off board misc. | |
| 1 | 125C3A choke |
| 1 | 40x20x20x20 filter cap or 5 22/500v caps |
| 1 | 40x20x20x20 cap clamp |
| 5 ft | Each Red, Black, White, Green 20GA Solid core wire or cloth wire |
| 5 ft | 18 Gauge Heater wire or cloth wire |
| 5 ft | Mini shielded cable if shielding is needed. |
| 6 | #8 Ring terminals |
| 6 inches | Heat shrink tubing |
| 1 | 6 Lug terminal strip |
| Assortment of #4, #6 and #8 screws, nuts and washers, depending on what you are mounting. Get 20 of each to have on hand. | |
| Circuit board 1/2 watt resistors | |
| 1 | 820 OHM |
| 2 | 2.2K |
| 1 | 47K |
| 4 | 100K |
| 5 | 47OK |
| Circuit board 3 watt resistors | |
| 1 | 4.7K |
| 1 | 10K |
| 2 | 1K |
| Circuit board 10 watt resistors | |
| 1 | 130 Ohm or 150 ohm |
| Circuit board capacitors | |
| 1 | .0047 Mallory 150 - 400 volt or higher |
| 2 | .01 Mallory 150 - 400 volt or higher |
| 4 | .022 Mallory 150 - 400 volt or higher |
| 1 | .68/250V |
| 1 | 47uf/100v cathode cap |
| Circuit board misc. | |
| 4 | 1/4" Nylon standoffs |
| 4 | #8 x 5/8" screws |
| 4 | #8 Nuts |
| 1 | Hoffman Stout Turret Board |
| 44 | Turret lugs - 52 if you are doing relay switching |
| On board Relay stuff - Optional Mod | |
| 1 | Relay socket |
| 1 | 5 volt signal switching relay |
| 1 | 1N4001 or 1N4007 Diode |
| Relay power supply board - Optional Mod | |
| 1 | Bridge #1 - See my web catalog |
| 2 | 4700uf/16V caps |
| 1 | 1/2 watt dropping resistor - 100 ohm will work |
| 1 | 1/8" Thick circuit board x 1.5" wide x 3" long |
| 7 | Turret lugs |
Enter My Tube Amp Parts Store Here
Mobile users Enter My Tube Amp Parts Store Here
The Tube amp Library of information
Click the link above for Tube amp info, Schematics, Board building information, Projects, Mods, Transformer diagrams, Photo's, Sound clips.
There are hundreds of pages of Tube amp information on my library page.
Please visit my Tube Amplifier Forum
Here's the place you can go to ask tube amplifier questions.
You will find a large community of friendly amp builders at the link above.
Check the huge library of Schematics here
Design your own custom Turret Board or Eyelet board
DIY Layout Creator file analyzer program
DIY Layout Creator file library
How to email me
|
MEMBER OF PROJECT HONEY POT Spam Harvester Protection Network provided by Unspam |